Ultra Wet Look

Looking to Purchase?

Visit Product Page
Seal ‘n Lock Ultra Wet Look® paver sealer is an advanced sealer with Nano Technology, high solids, low VOC modified acrylic urethane for a wet look enhancement. Seal ‘n Lock Ultra-Wet-Look® paver sealer penetrates the pavers and provides a long-lasting protective barrier with excellent joint stabilization. Ultra-Wet-Look® paver sealer is formulated to seal products made to ASTM C-936 specifications and an absorption rate of 5% or less. Pavers with a higher absorption rate will require an additional application(s) of sealer.
Ultra Wet Look® paver sealer is user-friendly and environmentally safe. The high solids content wears evenly and lasts longer than solvent-based paver sealers.
All Seal ‘n Lock products are made of the most environmentally-friendly products available, and offer excellent weatherability, UV protection, and help prevent algae and mold. All of our cleaning and sealing products and specialty coatings are VOC compliant in all 50 states and exceeds all hardscape product manufacturer’s minimum standards guidelines.

ULTRA WET LOOK® BENEFITS:

  • Superior Joint Stabilization
  • Beautiful Enhancement
  • High Solids
  • Minimal toxic odor
  • Will not harm vegetation
  • Provides a Protective Barrier
  • No need for polymeric sand
  • UV Protection
  • VOC compliant in all 50 states
  • One day process (No downtime)
  • It May be applied to a damp surface
  • Inhibits Algae & Mold Growth
  • Inhibits weed growth and ant mines
  • Hot tire marking resistant

ESTIMATING GUIDE

Typically, the application rate will vary from 150 to 200 sq. ft. per gallon, although this rate will vary depending on the texture, absorption rate of the surface and the width of the paver joints.

DIRECTIONS FOR USE

We recommend wearing protective goggles and latex gloves. For best results, apply Ultra Wet Look® paver sealer at temperatures between 60° F and 90° F. In cooler conditions, the paver sealer should be warmed to approximately 70° F. Do not apply if the surface or ambient temperature s below 50°F. A test for compatibility, penetration, and adhesion is recommended. If the temperature is going to drop below freezing (32° F) make sure the sealer has time to cure.

MIXING

Ultra Wet Look® paver sealer is designed to be diluted with 1 part water to 1 part sealer. Ultra Wet Look® paver sealer requires mixing (2 minutes) prior to use. We recommend 2 coats. Pavers with high absorption rate will require additional top coats of sealer to provide a protective barrier and desired enhancement. Ultra Wet Look® is not intended for submerged surfaces.

DRYING TIME

Ultra Wet Look® paver sealer will normally dry in sunny areas within approximately 1 hour. Shaded areas, lower temperatures or high relative humidity will slow the drying process. The surface may be open to foot traffic in 24 hours and to vehicular traffic in 48 hours. To minimize tire marks, vehicles should not make sudden stops or tight turns.

CLEANUP

  1. Immediately flush and agitate the pump system after sealing with a mixture of 3 gallons of water and 4 ounces of Formula FS.
  2. Flush out the pump system with 5 gallons of freshwater.
  3. Run 2 gallons of water through the system to flush any remaining chemical or sealer.  
  4. Always run water through the pump prior to the next application.

NOTES

Pavers with a high absorption rate will require additional top coats of sealer to provide a protective barrier and desired enhancement.
Ultra Wet Look® is not intended for submerged surfaces.

MAINTENANCE

Periodic washing of pavers with a mild detergent to keep the area clean is recommended.
DO NOT USE ACIDS : Gasoline, hydraulic fluids and motor oil spills should be removed from the surface of the pavers as soon as possible. We recommend that surfaces previously sealed with Natural Luster® should be cleaned and resealed every 3 years, depending on environmental exposure and traffic.
CAUTION : Too many coats of sealer may induce a slippery condition. May be slippery during the application if walked on. May cause skin and eye irritation. Do not take internally. Wear a mask while applying. All label directions should be read thoroughly before use.
View Products SDS