Super Wet Look

Super-Wet-Look

Super Wet Look® Paver Sealer from Seal n Lock is a high solid, two-part water-based pure urethane sealer that penetrates the pavers to provide a long-lasting protective barrier with superior joint stabilization (no need for polymeric sand) resulting in a wet look.
Super Wet Look® is user-friendly and environmentally safe. The high solids content of pure urethane wears evenly and lasts longer than solvent-based sealers.
All Seal ‘n Lock products are made of the most environmentally-friendly products available, and offer excellent weatherability, UV protection, and help prevent algae and mold. All of our cleaning and sealing products and specialty coatings are VOC compliant in all 50 states and exceeds all hardscape product manufacturer’s minimum standards guidelines.

SUPER WET LOOK® BENEFITS:

  • One day process (No downtime)
  • Provides a Protective Barrier
  • It May be applied to a damp surface
  • User friendly and environmentally safe
  • High Solids
  • Minimal toxic odor
  • Will not harm vegetation
  • Inhibits weed growth and ant mines
  • Superior joint stabilization
  • No need for polymeric sand
  • VOC compliant in all 50 states
  • UV Protection
  • Two-Part Urethane
  • “Wet Look” color enhancement
  • Hot tire marking resistant

ESTIMATING GUIDE

Typically, the application rate will vary from 150 to 200 sq. ft. per gallon, although this rate will vary depending on the texture, absorption rate of the surface and the width of the paver joints.

DIRECTIONS FOR USE

We recommend wearing protective goggles and latex gloves. For best results, apply Super Wet Look® at temperatures between 60° F and 90° F.
In cooler conditions, the sealer should be warmed to approximately 70° F. Do not apply if the surface or ambient temperatures below 50°F. A test for compatibility, penetration, and adhesion is recommended. If the temperature is going to drop below freezing (32° F) make sure the sealer has time to cure.

MIXING

Super Wet paver sealer should be diluted, after mixing part-A and part-B, 3 parts water and 1 part sealer for the flood coat and 1 part water and 1 part sealer for top coats. After mixing, the product must be used within two (2) hours and cannot be stored for future use.

DRYING TIME

Super Wet Look® sealer will normally dry in sunny areas within approximately 2 hours. Shaded areas, lower temperatures or high relative humidity will slow the drying process. The surface may be open to foot traffic in 24 hours and to vehicular traffic in 48 hours. To minimize tire marks, vehicles should not make sudden stops or tight turns during the curing process

CLEANUP

  1. Immediately flush and agitate the pump system after sealing with a mixture of 5 gallons of water and 4 ounces of Formula FS.
  2. Flush out the pump system with 5 gallons of freshwater.
  3. Run 2 gallons of water through the system to flush any remaining chemical or sealer.  
  4. Always run water through the pump prior to the next application.

NOTES

Pavers with a high absorption rate will require additional top coats of sealer to provide a protective barrier and desired enhancement.
Natural Luster® is not intended for submerged surfaces.

MAINTENANCE

Periodic washing of pavers with a mild detergent to keep the area clean is recommended.

View Products SDS - Part A
DO NOT USE ACIDS : Gasoline, hydraulic fluids and motor oil spills should be removed from the surface of the pavers as soon as possible. We recommend that surfaces previously sealed with Natural Luster® should be cleaned and resealed every 3 years, depending on environmental exposure and traffic.
CAUTION : Too many coats of sealer may induce a slippery condition. May be slippery during the application if walked on. May cause skin and eye irritation. Do not take internally. Wear a mask while applying. All label directions should be read thoroughly before use.
View Products SDS - Part B